Bill Parks's community posts
convoluted host connection
Bill Parks, User (Posts: 1)
Feb 25, 2019 4:22:47 pm EST
Support level: Free or trial
Windows 7, Remote host version 6.10.5.0
host ip is behind two routers (one mine, one isp fiber provider) and this is located in Myanmar which complicates it further as the entire country doesn't follow IANA.
Parkshost (my internal network is 192.168.100.1 gateway with the host pc on 192.168.100.100)
The Fiber router is Device Type: HG8045H
Description: EchoLife HG8045H GPON Terminal (CLASS B+/PRODUCT ID:2102310YYM6RH2001207)
SN: 48575443EEEFFC8D (HWTCEEEFFC8D)
Hardware Version: 534.B
Software Version: V3R013C10S126
Manufacture Info: 2102310YYM6RH2001207.C412
ONT Registration Status: O5(Operation state)
ONT ID: 14
and the wan info is
WAN Name Connection Status IP Acquisition Mode IP Address Subnet Mask VLAN/Priority MAC Address Connected
1_INTERNET_R_VID_1103 Connected PPPoE 172.18.130.101 255.255.255.255 1103/0 70:79:90:EE:EF:FD AlwaysOn
WAN Information
MAC Address: 70:79:90:EE:EF:FD
VLAN: 1103
Policy: Use the specified value
Priority: 0
NAT: Enable
IP Address/Subnet Mask: 172.18.130.101/255.255.255.255
Gateway: 172.18.159.254
DNS Servers: 103.233.204.12 8.8.8.8
BRAS Name: BNG_PRIMARY
and I am using port 4
1_INTERNET_R_VID_1103 1103/0 IPv4
The internal address of this is 192.168.10.1
this is a port 4 vlan off the fiber router which is 172.18.130.101 vlan 1103 which is provided by 5BB ISP in Myanmar with a host of 172.18.159.254 . They have an external address of 103.231.92.198 (as per WhatsMyIP)
I have access to the fiber router, and ParksHost routers, along with route tables.
This is beyond my ability to determine where the host software should point (obviously not 192.168.100.100 which is where it is now) what do I change it to, and what facilities will allow me to traverse the vlan and double NAT of the two routers? If it helps I can represent this pictorially. ParksHost router is TP-N750. System works fine and has been bulletproof, but now I am trying to access remotely and RU was suggested.
host ip is behind two routers (one mine, one isp fiber provider) and this is located in Myanmar which complicates it further as the entire country doesn't follow IANA.
Parkshost (my internal network is 192.168.100.1 gateway with the host pc on 192.168.100.100)
The Fiber router is Device Type: HG8045H
Description: EchoLife HG8045H GPON Terminal (CLASS B+/PRODUCT ID:2102310YYM6RH2001207)
SN: 48575443EEEFFC8D (HWTCEEEFFC8D)
Hardware Version: 534.B
Software Version: V3R013C10S126
Manufacture Info: 2102310YYM6RH2001207.C412
ONT Registration Status: O5(Operation state)
ONT ID: 14
and the wan info is
WAN Name Connection Status IP Acquisition Mode IP Address Subnet Mask VLAN/Priority MAC Address Connected
1_INTERNET_R_VID_1103 Connected PPPoE 172.18.130.101 255.255.255.255 1103/0 70:79:90:EE:EF:FD AlwaysOn
WAN Information
MAC Address: 70:79:90:EE:EF:FD
VLAN: 1103
Policy: Use the specified value
Priority: 0
NAT: Enable
IP Address/Subnet Mask: 172.18.130.101/255.255.255.255
Gateway: 172.18.159.254
DNS Servers: 103.233.204.12 8.8.8.8
BRAS Name: BNG_PRIMARY
and I am using port 4
1_INTERNET_R_VID_1103 1103/0 IPv4
The internal address of this is 192.168.10.1
this is a port 4 vlan off the fiber router which is 172.18.130.101 vlan 1103 which is provided by 5BB ISP in Myanmar with a host of 172.18.159.254 . They have an external address of 103.231.92.198 (as per WhatsMyIP)
I have access to the fiber router, and ParksHost routers, along with route tables.
This is beyond my ability to determine where the host software should point (obviously not 192.168.100.100 which is where it is now) what do I change it to, and what facilities will allow me to traverse the vlan and double NAT of the two routers? If it helps I can represent this pictorially. ParksHost router is TP-N750. System works fine and has been bulletproof, but now I am trying to access remotely and RU was suggested.
